246 items in Australia under $10,000 for sale

Quick release coupling never used

Wanted Hilborn fuel injection for 4 cylinder engine, prefer to suit Nissan L Series motor, but can adapt, regards AJ

track car all wheel drive built for pheasant deputy 4 hr series aasa log book 2 sets of wheels radio intercom new clutch fitted new timing belt race brake pads cheap track car also suitable for production car racing

AP Racing CP6465-218 pull type master cylinder 21.8mm

3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE

In perfect condition excluding the large daggy seat, hydraulic brakes, tach/hour meter, balanced for a 85 kg driver so she goes really well in the corners around the back yard, an impulse buy new which ignored my age. So she has had little use, original tyres, your chance to grab a bargain and rip off a boomer at the same time. Phone will likely go to message, email rzgreenup@gmail.com

Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide

AP Single plate , plate is 10 7/8 spline presents as new measures 2.63 mm . Can post Australia wide

This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.

A Carbon Fiber rear three element wing for Hillclimb Time Attack cars. This wing has never been fitted to a car and is as new. I imported the wing from the UK at a cost of 5000GBP. The elements have hard points engineered into the structure for mounting and support. Main Element Length is 1720mm and cord is 300mm. Second element is 1720mm x 120mm and third element is 1720mm x 115mm. Each element can be adjusted or removed.

Ideal start for your track project. The BMW is in very good condition rust and damage free. It needs an engine rebuild with suspected rod bearing damage. Rebuild it or engine swap. Car is in Newcastle and whilst it runs it will need to be towed.

NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.

I have 19 available $40 each which is less the half price can post Australia wide

Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20

Astra CDTi production car, Holden factory race car built by PMM for the 2007 Bathurst 12 hour sponsored by Bendon, built to showcase the power of the new diesel Astra. Also competed in the 2009 12 hour for the Holdsworth family, did some production racing for a few years after but more recently just used as a fun track car. Very well built, 6 speed, DMS suspension, Racetech seat, Performance Box with power and external antenna, we use ex Toyota 86 semi slicks for very cheap fun. Would need harne

Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500