256 items under $10,000 for sale
Most Recent
Most Recent
Keyword
Price
Featured ads
All Results
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
32
Roll Cage
Daihatsu Charade 1986 G11 Turbo originally a turbo car ! CB80 T conversion - twin cam fresh rebuild inc. forged Pistons - new water pump - belt and gaskets Good paint - exterior Half Cage fuel cell in boot willwood brake conversion _ not complete spare near complete engine spare - donor car Will need completing sold as project - unfinished project car REQUIRES wiring - either standard ECU (supplied) haltech and loom $2000 extra brakes - need plumbing and finishing off turbo - eith
119 1
Roll CageLog Book
Think GT3 racing and it is impossible not to think of the Audi R8 LMS GT3. One of the most successful GT3 race car of the modern era, it has amassed 83 drivers’ titles internationally and 106 championship victories – as well as eight overall victories in 12-hour races (including a record three at the Bathurst 12-Hour) and 13, 24-hour victories. It more than meets the challenges posed on all racetracks in all climatic zones and has won titles in Saudi Arabia as well as in Central Europe, Asia, A
8
Roll CageLog Book
Astra CDTi production car, Holden factory race car built by PMM for the 2007 Bathurst 12 hour sponsored by Bendon, built to showcase the power of the new diesel Astra. Also competed in the 2009 12 hour for the Holdsworth family, did some production racing for a few years after but more recently just used as a fun track car. Very well built, 6 speed, DMS suspension, Racetech seat, Performance Box with power and external antenna, we use ex Toyota 86 semi slicks for very cheap fun. Would need harne
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
10
Registered
2001 gen7 zzt231 celica 6 speed, Trd , rotrex supercharger,front mount intercooler etc. Has engineering cert in tasmania. Looking for a new project ?( i have another project taking my time and energy for now)This car has a blown motor after throwing a rod.Needs new block, 1 x mahl piston and rod,machining.The head/valves and crank seem ok.The motor/ supercharger had 50k on it after complete rebuild.(motor was over revved )after clutch problem. As far as power it was running 275kw atw @ 7psi o
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
11
Pedal Sliders Designed & Manufactured in Australia by PE Racing These are specifically designed to suit our PE Racing Pedal Assemblies and cater for the FIA fixed seat regulations. A little about our Pedal Assembly. This PE Racing Patented Frame design came about as a result of common problems experienced while installing pedal assemblies to a range of race cars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forces ultima
10
Load Spreading Washers - with 12mm locating shoulder to underside. How often do you find the panels you mount end up with the holes flogged out? Simple but effective, we designed this washer with a locating shoulder on the underside. This provides better lateral support for the connection. It reduces the bearing load by increasing the connection hole surface area. This results in less movement & reduced wear. Manufactured of Aircraft alloy in a range of sizes to suit M5, M6 & M8 counters
4
Complete set of original Porsche 997.2 S4 wheels and tires approx. 40% worn As new with no scrapes or blemishes. Fronts 19X8 235X35X19 Perilli "P" Zero Rears 19X11 305X30X19 Perilli "P" Zero
8
2004 Subaru Forester This was our shops hill climb/super sprint project but due to our current racing we are short on time to finish. Car is running, driving and operates fully. Interior stripped, racing seat and harnesses fitted, harness bar Fuel surge system installed BC Racing coil over kit installed 4/2 pot brake WRX calliper kit with associated bracketry to install supplied, modifications have been carried out to fit the kit, just needs instillation. 17 inch WRX light weight wheels wit
10
PE-Clamps are a quick & easy solution to mounting panels, cables, plumbing or accessories securely to common tube and roll cage sizes; eliminating the need for welding. PE clamps come in four different styles and a variety of sizes to satisfy a wide range of tube mounting needs. The images show a small example of potential uses. We have Engineered these to withstand a 10G dynamic load of 5 kg (equivalent to a static load of 50 kg) per clamp. The clamps have an optional vibration insulator th
6
ADL2 Motec Dash Good Working Condition Supplied with new harness and connector as supplied by Motec QLD Also supplied with pinout sheet Brisbane
10
Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This Patented Frame Design includes; Adjustable Mounting Feet, Fits easy to a variety of floor shapes. Adjustable Pedals Faces and, Adjustable Throttle geometry. High Quality, Reliable, Light, Strong & Fully Adjustable. This advert is for 2 Pedal Billet Frame Kit only for $1224 Aud (excl GST). 3 Pedal Billet Frame Kit is also available for $1673 Aud (excl GST). The Billet 2 & 3 Pedal Frame Assemblies come with, Levers, Ped
10
PE Racing offers you lightweight, reliable & high-performance Racing Pedal assemblies with Patented adjustable features to suit your driving style & increase performance. Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This PE Racing Patented design came about as a result of common problems experienced while installing pedal assemblies to a range of racecars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forc
5
Four x 45DCOE Weber carburettors on a Bolling Cross Flow Manifold linkages. Limited use. Very good condition.
3
Move that trailer effortlessly with Camper Trolly 2500kg load weight. Supplied with charging cable, remote controller and trailer leg attachment. priced well below new value.