115 items for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17
17
Lucas Fuel Injection off Lotus Twin Cam 6mm Metering unit, High pressure electric pump with filter. belt driven low pressure pump metering unit with drive throttle bodies slides in very good condition. Has been in storage for a number of years, I would recommend new lines and a check through before using. Can be freighted Australia wide or International must be with insurance .
6
AP Single plate , plate is 10 7/8 spline presents as new measures 2.63 mm . Can post Australia wide
2
Near New M800 and Data Logger Dash has not been used I owned as a spare for my FD RX7 Racecar. features enabled are as follows: M800 SN1323 single lambda, Hi/lo injection, Cam control, Advance functions (Traction control, Launch Control, Gear Ign cut, Overun boost) Dash ADL Dash SN 2732 shift / warning lights 1mb logging, Pro logging, standard inputs, See attached screen shot
3 1
This is a engine I got from purchasing a chassis i was after, so all parts are for sale. This auction is for a 600hp 873Nm touque @ 5500rpm, turn key engine eveything from coils, headers, drysump set up. It has alloy 23 degree heads, 180 degree headers. JE Pistons Scat 4340 crank Manley I beam conrods Brodix 23 degree alloy heads Comp cam roller camshaft Demon carburetor Crane ignition, with Crane ignition coil, MSD Distributor, MSD Leads, Custom MRX steped headers F1 merge collector's Runs o
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
5
Xtrac Sequential 6 speed. BMW M54 bellhousing and drive output, with E46 crossmember. New flywheel and release bearing. Pneumatic or lever shifted. Lever included (No paddles included)
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
14
Roll Cage
Chevrolet camaro 1968 drag car tabbed 15 inch wide wheels Dana diff front fiberglass clip imported from states. . Cage so much work in car left hand drive set up for big block Chevrolet twin turbo also have pipes made for twin gt42s
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
4
350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f
4
Race Simulator. Any car any Track, including rally. As new condition 3 x Screens. Sequential, Paddles and H Pattern Gears. Great fun Drive.
8
Tilton 800 series floor mounted pedal box c/w clutch, brake, throttle pedals. Pedal box is complete with 78 series spherical mounted brake master cylinders, and 76 series flange mounted clutch master cylinder. Is mounted to large alloy base and have cover to bolt over top of cylinders Comes with balance bar and adjusting cable Some options available, as have spare new cylinders, braided lines etc. Can discuss what is needed.
5
4 x Porsche Turbo cup wheels, phone Lee on 0419200201 for any information please.
6
samsonas gearbox SR20 Bell housing H pattern , Shifter Tail shaft , crossmember like new, One track day! ph 0418818419 cash talks
16
Roll CageLog Book
1956 Ford Crown Victoria Current IHRA & ANDRA Tech and Log book. Was NHRA certified 25.4B (7.50) Chris Alston Chassis Works (USA) "Eliminator II" full mild steel tube chassis, Front Coil over Spindles, Adjustable 4 Bar, Wheelie Bars. Body. All original steel in great condition with no rust Includes front bumper and indicator cowl Powdercoated aluminium interior Lexan windows with factory chrome Cool nostalgic/ratrod look with rusty bumpers, satin black painted body Deep Blue metalflake roof, das
9
Professionally New Built Can be registered Willwoods Brakes All Round Build for 1,500 HP Call 0413 878 516 $40,000
2
DSSV Damping Technology shocks Originally from a SCCA title wining Prototype D Sports Racer. Used for testing and one 13 lap race.
1
Selling a set of K&A Engineering Double up safety stands to suit a Porsche 991 cup car, in excellent condition, like new!
6
Brand new never used Samsonas RS90 transmission with T10 adapter, clutch shaft, shifter, strain gauge for shift cut and temp sensor. 1400nm rated. Located Kilsyth Victoria, can ship nationally if required. Only selling as the vehicle build has changed direction and requires a H pattern. Price is plus GST.