243 items under $10,000 for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
5
A Carbon Fiber rear three element wing for Hillclimb Time Attack cars. This wing has never been fitted to a car and is as new. I imported the wing from the UK at a cost of 5000GBP. The elements have hard points engineered into the structure for mounting and support. Main Element Length is 1720mm and cord is 300mm. Second element is 1720mm x 120mm and third element is 1720mm x 115mm. Each element can be adjusted or removed.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
8
2012 tandem race car trailer Beaver tail Hidden pull out ramps Electric winch Will come with a new battery Breakaway system Deck is 14ft Total length of trailer and draw bar is 20ft Inside the guards are 1,900mm The total width of the trailer is 8ft Registration until November
5
This car trailer is in near-new condition. Built in October 2021. Used to carry race car. 4.83m long and 2.0m wide at the tray. Wider and longer than usual. Has been stored inside my warehouse when not in use, never outdoors. Has extra shackle loops, manual winch and long ramps. Licensed and ready to use.
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
11
Pedal Sliders Designed & Manufactured in Australia by PE Racing These are specifically designed to suit our PE Racing Pedal Assemblies and cater for the FIA fixed seat regulations. A little about our Pedal Assembly. This PE Racing Patented Frame design came about as a result of common problems experienced while installing pedal assemblies to a range of race cars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forces ultima
10
Load Spreading Washers - with 12mm locating shoulder to underside. How often do you find the panels you mount end up with the holes flogged out? Simple but effective, we designed this washer with a locating shoulder on the underside. This provides better lateral support for the connection. It reduces the bearing load by increasing the connection hole surface area. This results in less movement & reduced wear. Manufactured of Aircraft alloy in a range of sizes to suit M5, M6 & M8 counters
4
Complete set of original Porsche 997.2 S4 wheels and tires approx. 40% worn As new with no scrapes or blemishes. Fronts 19X8 235X35X19 Perilli "P" Zero Rears 19X11 305X30X19 Perilli "P" Zero
6
ADL2 Motec Dash Good Working Condition Supplied with new harness and connector as supplied by Motec QLD Also supplied with pinout sheet Brisbane
5
Four x 45DCOE Weber carburettors on a Bolling Cross Flow Manifold linkages. Limited use. Very good condition.
3
Move that trailer effortlessly with Camper Trolly 2500kg load weight. Supplied with charging cable, remote controller and trailer leg attachment. priced well below new value.
6
All steel enclosed car trailer. Built to fit Austin Healy Sprite. Car space is 1320h x 1550w x 4000mm long. Gas struts on rear door. 200AH AGM battery installed 10/6/21. New tyres fitted in 2022. Serviced with new wheel bearings about 1000km ago. Inside and outside led lights. Internal gazebo rack. 4000kg winch.
5
Electric Club Car brand Golf Buggy with body kit and mag wheels. Comes complete with genuine Club Car Battery Charger. Immaculately maintained and kept. Only selling due to no longer required. Was originally purchased for my customers with GT cars to tow tyre trolleys and equipment to pit lane etc. Fits in an 8' x 5' box trailer for easy transportation. Note; Price +GST
7
8.2 Deck height Bought as spare but never used Suitable for turbocharging or supercharging It takes a Cleveland crankshaft and Cleveland camshaft Comes with front timing cover
4
Australian made Trailer Very little use 880kg trailer mass, 2500kg GCM. Internal dimensions: 1970mm wide by 4600mm long Optional stainless steel tire rack with capacity to hold a full set of spare wheels and tires included. Optional 1200mm high stainless steel stone guard included. Respray by PBS Specialty Coatings in Toowoomba. Paint failing after 2 years and no use hence the discounted price. Fully sand blasted, undercoated with Macro680, top coated with DULUX TB510 in Gun Metal Kinet