90 items for sale

4 spot 2018 Camaro Brembo calipers complete with pads. Apparently they will fit VE commodore uprights.

2 x Bridgestone re71rs tyres. 255 40 17 used on one track day. Clearing out the shed. Only selling as my car runs 16s and I bought these 17s to try on the car. I still run re71rs 16s on my car. They're a great tyre.

I bought this seat brand new from revolution race gear in Melbourne. It retails for $1450. They sold it to me for $1250 because there's a very small blemish in the leather near your right thigh. About 8mm long where something had been stacked on it. I fitted it to my VL race car on the weekend but due to the shoulder supports location i was unable to change gears comfortably. My loss is your gain.

I have a set of AP racing calipers to suit a commodore from VB to VS compatible with 330mm front and 300mm rear rotors. Selling as they don't fit under my wheels on my VL race car. I have 16 inch wheels. Comes with a set of unknown pads plus a set of circo competition fronts.

AP Racing CP6465-218 pull type master cylinder 21.8mm

3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE

Near New M800 and Data Logger Dash has not been used I owned as a spare for my FD RX7 Racecar. features enabled are as follows: M800 SN1323 single lambda, Hi/lo injection, Cam control, Advance functions (Traction control, Launch Control, Gear Ign cut, Overun boost) Dash ADL Dash SN 2732 shift / warning lights 1mb logging, Pro logging, standard inputs, See attached screen shot

This is a engine I got from purchasing a chassis i was after, so all parts are for sale. This auction is for a 600hp 873Nm touque @ 5500rpm, turn key engine eveything from coils, headers, drysump set up. It has alloy 23 degree heads, 180 degree headers. JE Pistons Scat 4340 crank Manley I beam conrods Brodix 23 degree alloy heads Comp cam roller camshaft Demon carburetor Crane ignition, with Crane ignition coil, MSD Distributor, MSD Leads, Custom MRX steped headers F1 merge collector's Runs o

This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.

NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.

350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f

4 x Porsche Turbo cup wheels, phone Lee on 0419200201 for any information please.

Perforated inner tube is top entry, bottom outlet. Small offset. 6" diameter case. 16" long. No spigots, 2 1/2" pipe slides into both ends then welded. $75 wholesale.

One only Challenger? alloy wheel. Zero curb rash. VGC. 14 x 7" on 4 3/4" pcd = HQ or Chev.