344 items in Australia for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
1
Brand new Albins ST6 6 speed with paddle shift. Front bell housing for clutch. Same as Marc car setup.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
6
This Truck was used to transport a race car. It comes with toolbox and ramps and ramp extensions for low vehicles. The tyres are almost new and serviced it regularly. It is a 3 seater and it’s very reliable. I still have to clean it out. Pan size is 6100 long 2450 wide and 2300 high. Low mileage 398000km.
1
I bought this truck as was, It was going to be the new Kumho Motorsport truck. (And my race truck on the side). F$%#kin TCR. It is set up to transport 1 car with a separate Kitchen/workshop area up front. It has room for a medium size sedan with the divider wall in but I have also seen this truck carry V8 Supercars. It is well set up with extender ramps to carry up to a 2500kg sedan. Since purchase, I have spent over $20K bringing it back to A1 spec. This spend included all the mechanical updat
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
12
PRICE CORRECTION 2007 Isuzu NPI 300 Pantech Truck 150HP Turbo Diesel Intercooled Motor 5 x Speed Manual, Air Conditioning, Electric Windows, Central Locking, Rear Camera Monitor System 2.0 Ton Tieman Cantilever Lift, 2.4 m Wide Platform. Includes Aluminum Platform Extension Ramps. Installed November 2018 Pan Internal Lift, 4000kg Hero Auto 4xPost Hoist activated by Nixons Engineering Hydraulic Power Pack 24 VDC with 12 Liter Tank. Installed April 2019 39HD H/Duty Rear Spring Set. Installed July
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
6
Type 9 Quaife Close Ratio Straight Cut Gearbox. Suit clubman of modified Escort. Never fitted to the car, went for a sequential 5 speed. All new bearings/gaskets and seals I think the Ratio: 2.2/1.69/1.21/1:1/0.873500
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
11
Pedal Sliders Designed & Manufactured in Australia by PE Racing These are specifically designed to suit our PE Racing Pedal Assemblies and cater for the FIA fixed seat regulations. A little about our Pedal Assembly. This PE Racing Patented Frame design came about as a result of common problems experienced while installing pedal assemblies to a range of race cars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forces ultima
4
350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f
10
Load Spreading Washers - with 12mm locating shoulder to underside. How often do you find the panels you mount end up with the holes flogged out? Simple but effective, we designed this washer with a locating shoulder on the underside. This provides better lateral support for the connection. It reduces the bearing load by increasing the connection hole surface area. This results in less movement & reduced wear. Manufactured of Aircraft alloy in a range of sizes to suit M5, M6 & M8 counters
4
Complete set of original Porsche 997.2 S4 wheels and tires approx. 40% worn As new with no scrapes or blemishes. Fronts 19X8 235X35X19 Perilli "P" Zero Rears 19X11 305X30X19 Perilli "P" Zero
10
PE-Clamps are a quick & easy solution to mounting panels, cables, plumbing or accessories securely to common tube and roll cage sizes; eliminating the need for welding. PE clamps come in four different styles and a variety of sizes to satisfy a wide range of tube mounting needs. The images show a small example of potential uses. We have Engineered these to withstand a 10G dynamic load of 5 kg (equivalent to a static load of 50 kg) per clamp. The clamps have an optional vibration insulator th
6
ADL2 Motec Dash Good Working Condition Supplied with new harness and connector as supplied by Motec QLD Also supplied with pinout sheet Brisbane
10
Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This Patented Frame Design includes; Adjustable Mounting Feet, Fits easy to a variety of floor shapes. Adjustable Pedals Faces and, Adjustable Throttle geometry. High Quality, Reliable, Light, Strong & Fully Adjustable. This advert is for 2 Pedal Billet Frame Kit only for $1224 Aud (excl GST). 3 Pedal Billet Frame Kit is also available for $1673 Aud (excl GST). The Billet 2 & 3 Pedal Frame Assemblies come with, Levers, Ped
10
PE Racing offers you lightweight, reliable & high-performance Racing Pedal assemblies with Patented adjustable features to suit your driving style & increase performance. Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This PE Racing Patented design came about as a result of common problems experienced while installing pedal assemblies to a range of racecars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forc
5
Four x 45DCOE Weber carburettors on a Bolling Cross Flow Manifold linkages. Limited use. Very good condition.