157 items for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
10
Lotus 7/ Clubman chassis. This car was raced by my father in the 70s and has been in storage since. Believed to be a Lotus 7 but cannot verify this, the only stamp I can find on the chassis is shown in the photos. Definitely not complete but includes many parts as pictured. Happy to answer any questions or arrange more photos if required.
3
AP Racing CP6465-218 pull type master cylinder 21.8mm
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE
3
Sydney Composites front splitter, used at WTAC in 2023 would suit either open class or Pro-Am, 2200mm wide and 810mm wide but can be reduced if required. Proven to produce massive down force with low drag. Titanium Wear Plates. Only selling due to changing direction. Happy to answer questions 0427700423 and can freight Austria wide
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
6
NO INTERNALS - This is a set of 3.2 engine cases with cylinders, heads and cam towers. What is shown in the photos. - 930/21 engine case, aluminium 5R and 6R with stamped matching case halves. - 930.104.325.4R Cylinder heads - 930.105.111. 2R Cam towers Note: Ex race car engine which is blank where the engine number would be. Would suit race build or would have to be re-birthed to use on the road. Also have internals if interested.
3
I have 19 available $40 each which is less the half price can post Australia wide
2
Porsche 996 997 Centre lock wheel travel nuts Can post Australia wide for $20
14
Roll Cage
Chevrolet camaro 1968 drag car tabbed 15 inch wide wheels Dana diff front fiberglass clip imported from states. . Cage so much work in car left hand drive set up for big block Chevrolet twin turbo also have pipes made for twin gt42s
8
Sr20de fully rebuilt. Custom made pistons for 14:1 compression, h beam rods, big crow cams, golbys adjustable cam gears, gtir intake manifold. Block was cleaned, decked and machined. Crank shaft was machined and balanced. Light weigh under drive harmonic balancer. Head was cleaned tested machined and ported. Comes with brand new clutch kit with a light flywheel. Engine is ready to bolt in and run.
4
350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f
6
ADL2 Motec Dash Good Working Condition Supplied with new harness and connector as supplied by Motec QLD Also supplied with pinout sheet Brisbane
2
Brand new still in box as it arrived from the US WYO Billet Lock Up Unit Includes Trans Dump Valves for air shifting gearbox Was planned to work with a 5 speed Liberty Cost $24,000 to land here from the US and they are more now Save $4,000 and 6 months wait!!
10
Rx7 built in 2014 By Jeff Holland JB Fabrication Central Coast. Has run a 6.4 1/4 mile Carbon front clip fibre glass rear half including doors (Comes with moulds for front clip & doors) Strange front spindle single adjustable shocks with TBM twin piston brakes light weight Rear shocks double adjustable both just been serviced. Strange 4 piston brakes and steel discs. 2 fire bottles 2 parachutes new cables cylinder springs 2 new 15x15 weld rims DBL with new 33x15x15s slicks Front spindle wel
4
Race Simulator. Any car any Track, including rally. As new condition 3 x Screens. Sequential, Paddles and H Pattern Gears. Great fun Drive.
3
New Wiseco pistons New bearings Carrillo rods Internally balanced crank Solid roller Crow cam reground Crane roller lifters Aluminium Yates Roush C3 heads Titanium inlets, stainless exhaust valves T & D shaft mounted rockers, as new Ford Motorsport High Rise Manifold Fully studded heads and main caps Isky springs High volume oil pump High volume water pump
5
4 x Porsche Turbo cup wheels, phone Lee on 0419200201 for any information please.
16
Roll CageLog Book
1956 Ford Crown Victoria Current IHRA & ANDRA Tech and Log book. Was NHRA certified 25.4B (7.50) Chris Alston Chassis Works (USA) "Eliminator II" full mild steel tube chassis, Front Coil over Spindles, Adjustable 4 Bar, Wheelie Bars. Body. All original steel in great condition with no rust Includes front bumper and indicator cowl Powdercoated aluminium interior Lexan windows with factory chrome Cool nostalgic/ratrod look with rusty bumpers, satin black painted body Deep Blue metalflake roof, das
4
Getrag M51 5 speed Volvo Dogleg 1st 1:1 5th 1st - 3.99:1 2nd - 2.58:1 3rd - 1.77:1 4th - 1.27:1 5th - 1.00:1 10x 29mm input spline Has speedo output to suit rally car Output Flange to suit Group A spec cars Sierra Volvo Mercedes etc Never been in a race car and in excellent condition Located on Gold Coast, Freight opitions available
4
Roll Cage
This cart is bran new, perfect for towing, 400cc petrol engine, The best quality tool box or promo box you would find, This cart is perfect for a promo vehicle , Call for more details