150 items for sale
Most Recent
Most Recent
Keyword
Price
Listing Type
Featured ads
All Results
10
Lotus 7/ Clubman chassis. This car was raced by my father in the 70s and has been in storage since. Believed to be a Lotus 7 but cannot verify this, the only stamp I can find on the chassis is shown in the photos. Definitely not complete but includes many parts as pictured. Happy to answer any questions or arrange more photos if required.
10
Ford Escort 2.1 YB N/A 231HP(on dyno) Cosworth type engine. Completely rebuilt as per pictures, New Cosworth Rods, ARP bolts, new bearings, 92mm Accralite piston 11:1 comp, new valves, fully ported, poslished and bench flowed head, Cometic head gasket, New Burton BLF14 camshafts, New Tony Law extractors, Twin weber 45's, bosch dizzy. New Big wing Alloy sump, ready to race/rally or very fast road car. Currently on engine test rig, can be seen running before purchase. As most people prefer to fit
3
AP Racing CP6465-218 pull type master cylinder 21.8mm
4
3SET KOYA SEMI FORGED WHEEL 2 SETS HAVE GOOD SLICK TYRES DUNLOP 1 SET HAS ARE WHITE WITH DUNLOP WET TYRES NOTE TYRE ARE 265/625 R17 NOTE WHEEL ARE FOR VR VS COMMODORE
17
Lucas Fuel Injection off Lotus Twin Cam 6mm Metering unit, High pressure electric pump with filter. belt driven low pressure pump metering unit with drive throttle bodies slides in very good condition. Has been in storage for a number of years, I would recommend new lines and a check through before using. Can be freighted Australia wide or International must be with insurance .
6
AP Single plate , plate is 10 7/8 spline presents as new measures 2.63 mm . Can post Australia wide
2
This is one of the diffs out of my VL commodore race car. It's got a pair of custom brackets to suit VS front calipers and the shock mounts have been cut off as well aa the car that it was in ran a rose jointed panhard bar with adjustable roll centre sonif you were going to use this housing it will require a bit of fab for your application. It's an M75/78 with 3.89 gears an a full 31 spline spool. Im great condition.
5
A Carbon Fiber rear three element wing for Hillclimb Time Attack cars. This wing has never been fitted to a car and is as new. I imported the wing from the UK at a cost of 5000GBP. The elements have hard points engineered into the structure for mounting and support. Main Element Length is 1720mm and cord is 300mm. Second element is 1720mm x 120mm and third element is 1720mm x 115mm. Each element can be adjusted or removed.
7
Hollinger 6 speed H Pattern gearbox with Chevy bell housing and input shaft and shifter included. It has receipts for overs $9,000 in reconditioned repairs to bring it up to Like new condition. These gearboxes are very rare, so jump the order queue and grab this one now
1
Brand new Albins ST6 6 speed with paddle shift. Front bell housing for clutch. Same as Marc car setup.
13
Our Latest Generation Load Cell Simulator Kit for PE Racing Billet Pedal Assembly Designed & developed to feel realistic, and handle real life pedal forces. PE Racing Load Cell Sim Racing Kit is designed for professional Motorsport Simulators & gaming. Designed to suit the Patented PE Racing Billet Pedal Box. Driving Simulators typically see more laps than real race cars, and thus these sim cylinders must withstand the same forces with increased cyclic loads. We have designed & developed thes
3
In very good condition located in Adelaide ideal for single seater period correct 50’s to 60’s or 70’s car.
11
Pedal Sliders Designed & Manufactured in Australia by PE Racing These are specifically designed to suit our PE Racing Pedal Assemblies and cater for the FIA fixed seat regulations. A little about our Pedal Assembly. This PE Racing Patented Frame design came about as a result of common problems experienced while installing pedal assemblies to a range of race cars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forces ultima
4
350 Fuel Injected Chev Engine, built as a project, only dyno time. Never installed to a car. 600BHP @7000. Autronic ECU & Harness, Miloden wet sump . SHP Dart 4 Bolt Block. Crower Crank. New parts include, NC'd Brodix Heads (1188106), stainless valves, Jessel Shaft Rockers, Brodix manifold (HV1814), CP Pistons & pins, Oliver 6" Rods, Isky roller cam 294: 302: 108. MSD dual Ignition 9:1 Comp ratio, tuned & mapped on 98 unleaded fuel. Very smooth & progressive. Ready to install. Ideal f
10
Load Spreading Washers - with 12mm locating shoulder to underside. How often do you find the panels you mount end up with the holes flogged out? Simple but effective, we designed this washer with a locating shoulder on the underside. This provides better lateral support for the connection. It reduces the bearing load by increasing the connection hole surface area. This results in less movement & reduced wear. Manufactured of Aircraft alloy in a range of sizes to suit M5, M6 & M8 counters
10
PE-Clamps are a quick & easy solution to mounting panels, cables, plumbing or accessories securely to common tube and roll cage sizes; eliminating the need for welding. PE clamps come in four different styles and a variety of sizes to satisfy a wide range of tube mounting needs. The images show a small example of potential uses. We have Engineered these to withstand a 10G dynamic load of 5 kg (equivalent to a static load of 50 kg) per clamp. The clamps have an optional vibration insulator th
10
Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This Patented Frame Design includes; Adjustable Mounting Feet, Fits easy to a variety of floor shapes. Adjustable Pedals Faces and, Adjustable Throttle geometry. High Quality, Reliable, Light, Strong & Fully Adjustable. This advert is for 2 Pedal Billet Frame Kit only for $1224 Aud (excl GST). 3 Pedal Billet Frame Kit is also available for $1673 Aud (excl GST). The Billet 2 & 3 Pedal Frame Assemblies come with, Levers, Ped
10
PE Racing offers you lightweight, reliable & high-performance Racing Pedal assemblies with Patented adjustable features to suit your driving style & increase performance. Designed for the Driver, NOT LIKE ANY OTHER FLOOR MOUNT PEDALS. This PE Racing Patented design came about as a result of common problems experienced while installing pedal assemblies to a range of racecars over many years. Initially a typical floor mount frame usually has a relatively short flat footprint, the brake pedal forc
5
Four x 45DCOE Weber carburettors on a Bolling Cross Flow Manifold linkages. Limited use. Very good condition.
5
Electric Club Car brand Golf Buggy with body kit and mag wheels. Comes complete with genuine Club Car Battery Charger. Immaculately maintained and kept. Only selling due to no longer required. Was originally purchased for my customers with GT cars to tow tyre trolleys and equipment to pit lane etc. Fits in an 8' x 5' box trailer for easy transportation. Note; Price +GST