335 items for sale

Hi Guys, Selling my R33 GTR as shown. This car is very well equipped and absolutely solid. Was formally used many moons ago as a Targa Tasmania entrant and as such could easily be used for this again. I purchased the car as a road going/registered car and used it as such for a year, then inevitably the itch got the better of me. I re-installed the cage, seats, and other items, lowered her back down again started using her for occasional sprints and time attacks etc Its never been used door to do

Genuine NASCAR R5 P7 engine (2 available) both fully rebuilt by Steve's Race Shop with components from Eatmon's Racing USA These are the proper 800hp+ engines originally run by Ernie Elliott NASCAR race team. Professional rebuild in Sydney ready for Sports Sedan racing and have not been raced as yet. All the good gear; Solid roller cam Roller keyway lifters Bryant crankshaft Carrillo rods Titanium valves and retainers NASCAR dry/vacuum sump Clevite bearings Total Seal rings etc, etc $35k e

Subaru GDB Sti 2005 – Circuit, Hillclimb, Rally Car Motorsport Australia Log Booked (State Level Circuit) AGI 6 Point Bolt in Cage (MA Registered) QLD Mod Plated EJ207 2.1L Stroker Engine built by Maximum Motorsport – Receipts available. Blouch Dominator 1.5XTR 10cm Turbo Subaru Genuine Nitrided Crank – 79mm ARP 625 Head Stud Kit Manley H-Beam Rods with ARP2000 Bolts Manley Platinum Series Pistons – 92.5mm Bore x 79mm Stroke ACL Race Series Main Bearings ACL Race Series Big End Bearings Link G

1980 vb sl/e commodore. 253 v8 automatic. Kept as original as possible. Always garaged barely driven. Has had brake system rebuilt and carby rebuilt a few years back. Has original purchase receipt also.

Built to Group A Homologation. Classic class eligible. Motorsport Australia (cams) log book. On Qld rally rego. Strut to strut national level registered cage. MCA Gold adjustable suspension. JA 2.0 Liter Turbo with intercooler. ARCom approved upgrade to Garret GT2560 turbo and mpi inlet manifold. EMS engine management. Rack & Pinion EPAS conversion. Dual brake master cylinders with adj balance bar. Wilwood 4 spot calipers and larger front rotors. Original rear disk brakes. Hydraulic hand brake.

FOR SALE EVO 4-9 1000HP PLUS RATED TWIN PLATE: Brand new unused Direct Clutch Services 8 inch twin plate ceramic clutch. The clutch was custom built and spec'd for Roll racing/Street (2800lbs clamping force, push type) use with power goals north of 1000hp at the wheels. Located in Brisbane, can arrange shipping anywhere in Australia at Buyers expense.

This Minetti has been a total rebuild of electrical with all Haltech equipment. This includes IC7 Display Dash, 2500 Elite ECU, 02 Wide Band Sensor, HPI4 Power Ignitor. The engine is a Gen 2 -1340cc Suzuki Hayabusa with 8 injectors and has the low profile sump with a 360 degree swivel pick up. The body is a new 1 piece lightweight version. Other equipment includes, new 6 point harness, MCA fully adjustable shockies front and rear, new Avon tyres only 2 meetings old, Dyna jet quick shift for flat

2018 Porsche 991.2 Cup car. Car was originally Porsche Sport Driving School Level 5 car. Then raced in Michelin Sprint Challenge by Lockie Bloxsom. The car has been meticulously maintained by McElrea Racing since new. Car has12941 km, engine 78.5 hrs, gearbox 5.5 hrs (25 hrs remaining), driveshafts 11hrs (less than half life). Car comes with Supercup exhaust, travel nuts, two spare sets of wheels, car cover, wheel socket and air lance. $275,000 plus gst.

Up for sale is our Corolla KE70, aka Nana-Spec, project car 4A-GE motor (originally out of MR2) ECU and wiring is completed Motor runs (needs the return fuel line back to the tank to be plumbed up) Hydraulic clutch installed, needs to be bled Surge tank and pump installed New exhaust system Original paintwork and interior Minor rust in lower rear outer quarter panel and front edge of bonnet, and small amount of panel work required Clean chassis and underneath Selling due to not having enough

Project car regrettably up for sale 4AGE-ZE motor with LA3 mod plate Cast iron Celica 5-speed gearbox Shortened Hilux diff 15” Simmons wheels Front mounted intercooler behind bar Very clean underneath, no rust in chassis Interior mostly complete, missing a couple of mouldings in boot area Exterior in good condition, a couple of small rust spots, nothing major Motor not currently running Will require ECU and partial rewire Selling due to not having enough time - have had the car for 8 years

It's time for my Humber Speedster project to be passed along to someone who can finish it. I had always wanted a pre-1920’s Speedster but as they don’t suit the highway driving of today I decided to make one from a car that could. The donor car was a ’32 Humber rolling Chassis. All the hard work has been done, and 99% of the materials and components purchased. I have chronicled the build in photographs and a blog, plus starting the engine for the first time on a video. When going through the par

1962 MORRIS MINI 850 FITTED WITH FUEL INJECTED YAMAHA R1 AND QUAIFE LSD HALTECH ECU FIBREGLASS LIFT OFF FRONT HALF ROLLCAGE VENTILATED ROTORS WITH 4 SPOT CALIPERS FRONT COILOVERS 2 FUEL TANKS HIGH AND LOW PRESSURE FUEL PUMPS 3 PIECE ALLOY WHEELS FITTED WITH HOOSIER TYRES 2 RACE SEATS 2X 5 POINT HARNESS NSW ENGINEERING PAPERS WAS REGISTERED IN NSW CURRENTLY REGISTERED IN QUEENSLAND